My 2002 BEGI S4 GT2860RS - White and sexy.
 

Hello All,

Picked up a 2002, recently sold a 91 Supercharged. I'm picky about my work and try to make the right moves with my stuff. I hope you enjoy.

Equipment:

2002 Miata LS White, black and tan interior
Corbeau FX1 Pro Suede Drivers Seat
OZ Superleggera 16
Tein S-Tech Springs, KYB Shocks

Performance:

BEGI S4 System with upgraded intercooler and GT2860RS option (Disco Potato)
AEM Water/Meth Progressive from 4-13 LBS (Not tuned as of now)
ACT Clutch on my third 5 speed trans
LSD Poly Differential bushings
FM turbo exhaust with high flow cat Poly exhaust hangers
AEM WB
TurboSmart E-Boost2 Controller
XEDE Piggy back
RC 550 injectors
Walbro 190 HP Fuel Pump
Upgraded radiator - Coolant Reroute
Marshall - Boost, Oil Pressure, Oil Temp gauges
Roll bar - Hard dog

I'm sure I'm missing things..

http://img835.imageshack.us/img835/2108/img1945.png

Looks good. Do you have any dyno sheets or anything?

AEM Meth/Water Install:

I decided to run the pump and the tank in the trunk. I pride my engine bay too much to be cluttering it up with another tank and a bunch of wires.

https://www.miataforumz.com/attachme...ine=1312294068


Kit didn't come with a bung so I hit up the local hardware joint and welded a nut.
https://www.miataforumz.com/attachme...ine=1312294068

Powder to cover up my gorilla welding.
https://www.miataforumz.com/attachme...ine=1312294068

Nice and clean...
https://www.miataforumz.com/attachme...ine=1312294068

I ran the smallest jet included with the AEM kit. Wired the fail output wire to my XEDE to switch maps when I get around to tuning for it. I expect to run some pretty aggressive timing and about 13 LBS.

The dyno sheet I have is not on 12.5 LBS. It's a bit lower and the car was not as equipped as it is now. Put down 255, if I recall it was around 10PSI? Unsure though.

Lightweight Battery installation:

Old mount was obviously too large. I didn't want to rice it up with some rigged up stuff though.
https://www.miataforumz.com/attachme...ine=1312294612

So I chopped the grip off and re-welded it to fit the new battery.
https://www.miataforumz.com/attachme...ine=1312294612

A little black paint, some new terminals and shrink wrap, and we're in business. Just can't leave my radio on as long when the car is off.
https://www.miataforumz.com/attachme...ine=1312294612

Radiator and fan installation:

We had a heat wave come through and the car started to overheat under some moderate beating-the------out-of-her driving. I didn't see any reason to dump 5 hundo on brand name aluminum when I was just looking for a little upgrade, so I ordered this guy off of eBay. Nice product, direct fit, and it absolutely did the trick. Threw some Mishimoto silicone on it. Product Link

Good looking radiator if you ask me. It's got a simple job. Good welds, factory mounting points.
https://www.miataforumz.com/attachme...ine=1312295189

Slid in with minimal fuss, looks good to me.
https://www.miataforumz.com/attachme...ine=1312295189

The slim fans made up for the additional size of the radiator. Mishimoto silicone was designed for the stock coolant route.. so that took some manipulating. Nothing to fuss about though.
https://www.miataforumz.com/attachme...ine=1312295189

Very nice project!

This is clean!

I love it !

Thanks man. More to come..

How much did you paid for the radiator?