Gauge Cluster Wiring Diagram
#1
Gauge Cluster Wiring Diagram
So I am wiring my monster miata up to my NB maita and trying to get the gauge cluster wired up does anyone know what pins are what for the NB cluster? Or have a diagram. Thanks.
#2
copied from BarbyCar in the LED gauge cluster thread....
Here is the pinout for the 2000 if that helps.
They are in the wiring diagram section C-a and C-b but for those without diagrams, here they are:
There are three connectors 1, 2 and 3. From the driver's seat 1 is on the left, 3 in the middle and 2 on the right. Each connector pinout starts at "a" and the blue circuit is labelled with an appropriately placed "a".
1a= BR/B - Fuel System (ECU and fuel gauge sender)
1b= BR/Y - Cruise Light (from cruise module)
1c= B/Y +12v Switched (from meter fuse)
1d= No wire or P/B - If applicable, ABS light (from ABS module)
1e= No wire or R/W - If applicable, Automatic O/D light (from transmission control module)
1f= L/R +12v Unswitched from Room fuse
1g= Not used
1h= W - DRL module (high beam light) - No wire if no DRL
1i= R/Y - Headlight relay (via LH headlight fuse) - note R if no DRL
1j= not used
1k= not used
1L= W/R - Door switch (interior lights)
1m= Y - Speed sensor for manual. No wire for automatic
1n= B/L - Ground
1o= not used
1p= V - Start signal - from ign switch on manual. B/R from transmission control module if auto
2a= V/W - Water temp (from temp sensor)
2b= L/W Seat belt (seat belt switch - driver's side reel)
2c thru 2j not used
2k= G/O - ECU (and data link connector - also transmission control module if auto)
2L= W/B - ECU and cruise control module
2m= O - Speed sensor for manual. B/W from transmission control module for auto
2n= not used - goes to empty lamp socket
2o= W/L - ECU - controls CEL
2p= not used
3a= G/B - Left turn signal
3b= BR/R - ECU
3c= L/Y - Brake fluid light (and DRL control module. If no DRL then also to parking brake switch)
3d= BR - Air Bag module (and data link connector)
3e= Y/R - Oil Pressure "gauge" switch
3f= L/O - Key reminder switch
3g= R/B - Instrument lights +12v from TNS relay
3h= GY/R - Instrument lights dimmer control to ground
3i= G/W - Right turn signal
3j= B - Ground (connects internally in cluster to high beam light if no DRL)
L=Blue, B=Black, BR=Brown, G=Green, GY=Grey, O=Orange, R=Red, W=White, Y=Yellow & V=Violet
Here is the pinout for the 2000 if that helps.
They are in the wiring diagram section C-a and C-b but for those without diagrams, here they are:
There are three connectors 1, 2 and 3. From the driver's seat 1 is on the left, 3 in the middle and 2 on the right. Each connector pinout starts at "a" and the blue circuit is labelled with an appropriately placed "a".
1a= BR/B - Fuel System (ECU and fuel gauge sender)
1b= BR/Y - Cruise Light (from cruise module)
1c= B/Y +12v Switched (from meter fuse)
1d= No wire or P/B - If applicable, ABS light (from ABS module)
1e= No wire or R/W - If applicable, Automatic O/D light (from transmission control module)
1f= L/R +12v Unswitched from Room fuse
1g= Not used
1h= W - DRL module (high beam light) - No wire if no DRL
1i= R/Y - Headlight relay (via LH headlight fuse) - note R if no DRL
1j= not used
1k= not used
1L= W/R - Door switch (interior lights)
1m= Y - Speed sensor for manual. No wire for automatic
1n= B/L - Ground
1o= not used
1p= V - Start signal - from ign switch on manual. B/R from transmission control module if auto
2a= V/W - Water temp (from temp sensor)
2b= L/W Seat belt (seat belt switch - driver's side reel)
2c thru 2j not used
2k= G/O - ECU (and data link connector - also transmission control module if auto)
2L= W/B - ECU and cruise control module
2m= O - Speed sensor for manual. B/W from transmission control module for auto
2n= not used - goes to empty lamp socket
2o= W/L - ECU - controls CEL
2p= not used
3a= G/B - Left turn signal
3b= BR/R - ECU
3c= L/Y - Brake fluid light (and DRL control module. If no DRL then also to parking brake switch)
3d= BR - Air Bag module (and data link connector)
3e= Y/R - Oil Pressure "gauge" switch
3f= L/O - Key reminder switch
3g= R/B - Instrument lights +12v from TNS relay
3h= GY/R - Instrument lights dimmer control to ground
3i= G/W - Right turn signal
3j= B - Ground (connects internally in cluster to high beam light if no DRL)
L=Blue, B=Black, BR=Brown, G=Green, GY=Grey, O=Orange, R=Red, W=White, Y=Yellow & V=Violet
#6
I've got one of these at the house. They are a good investment as a Miata owner.
I would scan the info but I'm not where it is.
I would scan the info but I'm not where it is.
Thread
Thread Starter
Forum
Replies
Last Post
jared8783
NA (1989-1997)
2
08-07-2011 12:10 PM